AUTONET TV

All Lined Up (Alignment Inspection)

When you head down a straight road, does your vehicle pull to one side?  Do you feel vibration in any of the wheels? If you've noticed any of these things, it's probably time for you to get your wheel alignment checked.

When your vehicle left the factory, its wheels were parallel to each other and perpendicular to the ground.  That maximizes traction for good steering and braking. Every time you take your vehicle on the road, normal wear and tear will affect your alignment. Hit a bump, a pothole or a curb and all those little knocks will add up

Bad alignment not only can cause your steering wheel to pull unevenly, it can also wear your tires out a lot faster than they should. In fact, if you look at your tires and see one side of the tread is a lot smoother than the other, it could be another sign of bad alignment.

Since different problems can cause similar symptoms, the first thing our trained technician will do is test drive your vehicle. Then, they'll check the front end and steering linkage as well as look for tire wear.  Then, the technician will put your vehicle on a lift and use computerized diagnostic equipment to measure alignment angles so they can precisely align your vehicle's components.

There are different kinds of alignments.  One is a front-end alignment that aligns components of the vehicle's front axle.  Another is a thrust alignment that makes sure the front wheels are lined up with the direction the rear wheels are pointed.  A third type is four-wheel alignment which is usually used on all-wheel drive and  4-wheel drive vehicles.  It's also recommended for front-wheel drive vehicles that have independent rear suspensions.  It makes sure the angles of all the wheels are where they should be relative to each other and also the vehicle's body or frame.

Your steering wheel should be perfectly centered if you are heading straight down the road, so the technician will adjust it so it is. Finally, they'll take your vehicle back on the road for a final test drive to make sure it's performing the way engineers intended.

Your service adviser can recommend how often you should have your alignment inspection, since it depends on the type of vehicle you drive (SUV, sporty car, etc.) and your driving environment.  Properly aligned wheels can help your vehicle perform better and save you from expensive repairs down the road.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, Connecticut 06010
(860) 589-1255

I Can See Clearly (Wiper Blade Replacement)

Warm weather can bring severe storms, and when the rain is coming down hard, that's one time you really need to be able to see as clearly as possible out your windshield.  Having wiper blades that are fit for the job are important to maintain that safe view.

Maybe you live in a climate where you use blades made for winter weather and you have haven't changed them since the weather changed.  Those blades are made of heavier materials and don't work as well in warmer temperatures. Blades made for warm temperatures are lighter and clear water better in the warmer months.

The general rule of thumb is you should change your blades every six months, but if you use them a lot, you might have to change them more often.  A couple of signs that your blades need changing? If you are seeing streaks on the glass or hearing a chattering sound when your wipers are working, time for a new pair.

Wiper blades have cleaning windshields on vehicles for more than 100 years.  The original designs have a multi-part frame that are better for flatter windshields.  But newer vehicle designs now have curvier windshields, so a more recent design is called a blade wiper.  It's designed to conform better to the glass so cleans it better. 

Conventional wipers also aren’t as aerodynamic as blade wipers. Wind buffeting can reduce the pressure they apply on the rubber to the glass.  With a spoiler as part of their design, blade wipers are pressed more tightly to the glass, an advantage in clearing water from it.

Another option is hybrid blades, essentially a conventional blade with a plastic shell around the wiper's frame that makes it more aerodynamic and, some say, gives it a more aesthetic look. 

There are lots of choices, so consult our service professionals for a recommendation on which blade fits your needs—and budget—best.  Keep your eyes on the road and keep your windshield sparkling clean, rain or shine.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, Connecticut 06010
(860) 589-1255

Them's the Brakes (Brake Rotor Resurfacing)

Your vehicle's brakes wear out.  It's inevitable. You'll notice it when you step on the brake pedal and feel it harder to stop, or there's vibration when you are braking. 

Most modern vehicles have disc brakes that each use a brake pad that press on a disc (disc brakes!) called a rotor.  The friction between them enables you to stop, and each time you do a little bit of the pad and the rotor wears down.

The original brakes on vehicles used a rotor that was thick enough to last through at least two replacements of the pads.  But vehicle manufacturers who want to save costs and weight now make them thinner, and sometimes the rotors have to be replaced after the first pad replacement.  But not always.

Vehicle manufacturers specify a minimum thickness to provide safe braking.  Sometimes rather than having to have your rotors replaced, they can be put on a lathe and resurfaced.  In other words, the surfaces of the disc can be slightly shaved off so the surface is flat and doesn't wobble. 

Whenever you bring your vehicle in to have the brakes checked, the technician will measure the thickness of the rotors to see if they can be resurfaced without leaving them too thin for safe braking. If they can, with the right tools and skill, the rotors can be resurfaced.  If not, the rotors should be replaced. 

Discuss the options with your service advisor.  Our service center can recommend replacements that are designed to help stop your vehicle as well as or better than the vehicle's original rotors.

Either way, keep in mind that keeping your brakes in top condition can supply the margin of safety that may one day save your life or the lives of those around you.

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, Connecticut 06010
(860) 589-1255

Shifty Letters PRNDL (Transmission)

You probably figured out those shifty letters.  They're what you see on your automatic transmission shifter and stand for Park, Reverse, Neutral, Drive and Low.  Your automatic transmission is one of the great automotive inventions; here are some ways you can keep yours working well.

Maintain your transmission regularly.  A technician will check your transmission fluid's level and even its appearance and smell.  If it's dark or has an unusual odor, that could be a sign of trouble.

Change from one transmission direction gear into another only when your vehicle is stopped.  So many drivers want to switch from Reverse to Drive quickly or the other way around.  If you do that when the vehicle is moving, you can damage your automatic transmission.

Keep your vehicle's cooling system in top shape.  What does the cooling system have to do with the transmission? It helps keep the transmission fluid from overheating. 

Follow the manufacturer's recommendations for maintaining your transmission.  Some recommend at least an annual checkup by a trained technician. 

Let your powertrain warm up a little before overtaxing it. Especially in cold weather, don't step on the throttle too aggressively before all components are warmed up.  That way both your engine and transmission will last longer.

Transmissions can be costly to fix.  If you treat your powertrain with respect and regularly maintain it, you'll not only avoid expensive repairs, but you’re also much less likely to find yourself stranded because of a transmission problem. 

Economy Transmission and Auto Repair
201 Terryville Road
Bristol, Connecticut 06010
(860) 589-1255